![]() ![]() ![]() The copier is about the same, registering about 3 copies per minute and a maximum of 99 duplicates per original. Rather than an 8-bit color depth, the C50 scanner offers triple that, at 24-bits, and it scans with a resolution of 400 ppi, 100 pixels better than the older unit. In fact, most of them lie in the quality of the scanner. The differences between the C50 and its predecessor, the C20 are subtle and minimal. There are a number of buttons on the top panel as well as an LCD display that are both in place to give users quick access to settings, status of tasks and simple navigation through the copying, scanning, printing and faxing options. However, looking closer it is easy to see that this is no ordinary printer. When the main menu appears, click Install MultiPASS Suite.With the classic white frame that has the input tray sitting upright on the backside of the unit and an output trays that jets straight out from the bottom, from a distance the Canon MultiPASS C50 looks like an average personal printer.In the Run dialog box, type the following command and click OK (where D: is the drive containing the installation disk or copied software): D:\csplash.exe. If installation does not start automatically, or you are installing from the software copied on another drive, do the following: On the Windows taskbar, click Start, and then click Run. If AutoRun is enabled, the installation starts automatically.If you are installing with a copy of the MultiPASS Suite located on another drive, skip to Step 5. Insert the installation disk into your disk drive.If a New Hardware Found, Update Device Driver Wizard, or Add New Hardware Wizard dialog box appears, click 'Cancel'. With your PC on, close any open applications (including any virus checkers). Connect your printer cable to the ports on your printer and PC.Make sure the printer and PC are turned off.To install the MultiPASS Suite (parallel port connection): If your PC does not restart automatically, restart it manually. When the installation is finished, restart your PC before using the MultiPASS Suite software. Continue to follow the on-screen instructions to complete the installation process.Once the cable is connected, if a system message appears indicating the system driver is being installed, wait until the installation process is completed, and then click 'Yes' to continue. When prompted, connect your printer cable to the ports on your printer and PC, so the printer can be automatically detected.When prompted, click your printer model.You will not be allowed to continue the installation process. ![]() When the main menu appears, click 'Install MultiPASS Suite'.In the Run dialog box, type the following command and click 'OK' (where D: is the drive containing the installation disk or copied software): D:\csplash.exe. If installation does not start automatically, or you are installing from the software copied on another drive, do the following: On the Windows taskbar, click 'Start', and then click 'Run'. With your PC on, close any open applications (including any virus checkers).Turn on the printer, but do not connect the printer to your PC until prompted, or the PC may attempt to install the software before the unit is ready.To install the MultiPASS Suite (USB port connection): If later you change your mind and prefer to connect to the other port, you must remove and reinstall the MultiPASS Suite. When you connect to the USB port, the parallel port on your printer is disabled and is not available while the USB port is being used. However, if your computer has a USB port available, it is recommended that you connect the printer to the USB port. If you are using Windows 98/Me or Windows 2000/XP: You can connect to the parallel port.Only a parallel port connection is supported in these operating systems. You can connect the printer only to the parallel port on your computer. If you are using Windows 95 or Windows NT:.When you install the MultiPASS Suite, you must choose the port type for the printer connection. To install the MultiPASS Suite software if you are using Windows NT/ 2000/XP, you must log on as Administrator or have Administrator privileges. MultiPASS Suite 3.x or earlier must be removed from your PC before installing MultiPASS Suite 4.x.Ĭlick on the below attachment for uninstall information The MultiPASS Suite should not be installed on a network drive. The MultiPASS Suite installation program installs all the appropriate software components on your local hard drive. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |